弹丸速度的数字化激光幕测试技术

针对传统弹丸速度测量方法的局限，提出一种新的弹丸速度测试技术——数字化激光幕结合互相关速度测量算法的测试技术，并给出了激光总体测速方案、测速原理以及互相关测速方法，经靶场试验验证测试效果良好。     

基于并行模拟的多核集群系统性能预测和分析

针对多核集群系统所表现出的新的性能特征,提出了面向多核集群系统消息传递应用程序的并行模拟模型并设计、实现了一个并行模拟器MCPSim(Multi-core Cluster Parallel Simulator),MCPSim在功能模型和性能模型上体现了片内核间、结点内片间以及结点间等三个层次上消息通信的特点,同时支持对应用的消息数量、通信量等的百分比分布的profiling功能,采用PRIMEJ、acobi3D、NPB IS以及HPL等Benchmark程序对MCPSim进行了测试,结果表明MCPSim性能预测的精度优于BigSim,同时能够广泛应用于针对多核集群系统消息传递应用程序的性能分析中。     

目标系统的测试软件设计

阐述了自动测试目标系统的软件设计,介绍了目标在移动过程中偏离瞄准线,产生偏差的情况下,自动测角仪与主控计算机之间的通信必要测试条件,相关的信号处理和控制手段,及如何提高自动测角仪测试系统的检测精度。     

多级感应线圈发射器测控系统设计

将电枢加速到较高速度，通常需要多级感应线圈连续加速；而提高多级感应线圈发射器的发射效率，则要求在电枢处于驱动线圈最佳触发位置时，电容器组同步放电。同时，需要采集发射过程中电枢的速度、电源的放电电压和放电电流等数据。因此，研制合理的测控系统是多级感应线圈发射器的关键。     

二维超声速空气引射器启动特性试验研究

超声速引射器是高空模拟试车台的重要组件,在发动机启动前利用引射器对试验舱预抽真空,可避免发动机启动初始时刻燃气漏入试验舱造成燃气在发动机中分离,对获取发动机在高空环境下的完整推力特性具有重要意义。而该工况下超声速引射器的启动过程是引射器工作过程中最为恶劣的工况,设计不合理的引射器会导致启动压力过高甚至不能实现启动。建立了缩比超声速空气引射器试验台对超声速引射器的启动特性进行研究,采用压力测量方法结合纹影技术对超声速引射器处于极限启动压比时的流场进行了描述,研究结果表明混合室收缩比越小,引射器极限启动压比越低。同时给出了定位超声速引射器不启动原因的判据:当引射器不启动是由引射总压不足引起时,盲腔压力在引射总压提高时降低,并在临界启动状态下达到最小值;而由混合室收缩比过小导致的引射器不启动在引射总压提高时盲腔压力单调上升。     

可靠性强化试验与加速寿命试验综述

介绍可靠性强化试验与加速寿命试验的基本概念 ,并进一步综述强化试验与加速寿命试验的国内外研究现状 ,最后对强化试验与加速寿命试验领域可能的研究方向进行归纳总结。     

RTI测试研究

运行支撑系统(RTI)作为应用高层体系结构(HLA)进行分布仿真的支撑系统,是实现HLA的核心。RTI的功能和性能直接关系到HLA仿真系统开发与应用的成败。首先阐述了RTI测试的内容和指标,接着结合例子详细研究了RTI测试的方法,最后对RTI测试研究进行了总结,为提高基于HLA的分布交互仿真系统的质量及可信度提供了基础。     

Fabrication of AA7005/TiB2-B4C surface composite by friction stir processing: Evaluation of ballistic behaviour

The present work aims to enhance the ballistic resistance of AA7005 alloy by incorporating the TiB₂ and B₄C ceramic reinforcement particles. Surface composites with different weight fractions of TiB₂ and B₄C particles were processed by friction stir processing. Micro-hardness and depth of penetration tests were carried out to evaluate the ballistic properties of the surface composites. The surface hardness of the composite was found to be nearly 70 HV higher than base alloy. The depth of penetration of the steel projectile was 20–26 mm in the composites as compared to 37 mm in the base alloy. Ballistic mass efficiency factor of the surface composite was found to be 1.6 times higher than base alloy. This is mainly attributed to the dispersion strengthening from the reinforcement particles.     

Effect of wave shaper on reactive materials jet formation and its penetration performance

Wave shaper effect on formation behavior and penetration performance of reactive liner shaped charge (RLSC) are investigated by experiments and simulations. The reactive materials liner with a density of 2.3 g/cm³ is fabricated by cold pressing at a pressure of 300 MPa and sintering at a temperature of 380 °C. Experiments of the RLSC with and without wave shaper against steel plates are carried out at standoffs of 0.5, 1.0, and 1.5 CD (charge diameter), respectively. The experimental results show that the penetration depths and structural damage effects of steel plates decrease with increasing the standoff, while the penetration depths and the damage effects of RLSC without wave shaper are much greater than that with wave shaper at the same standoff. To understand the unusual experimental results, numerical simulations based on AUTODYN-2D code are conducted to discuss the wave shaper effect, including the propagation behavior of detonation wave, the velocity and temperature distribution of reactive jet, and penetration depth of reactive jet. The simulations indicate that, compared with RLSC without wave shaper, there is a higher temperature produced inside reactive jet with wave shaper. This unusual temperature rise effects are likely to be an important mechanism to cause the initiation delay time of reactive jet to decline, which results in significantly decreasing its penetration performance.     

顶置武器站性能评估方法

在评估指标体系和虚拟样机仿真测试评估数据的基础上,对顶置武器站性能评估进行研究。对评估方法进行研究,提出了适合顶置武器站性能评估特点的灰色模糊综合评估法,选用灰色关联度分析计算指标权重,建立开放性的隶属矩阵,最终建立顶置武器站性能评估模型。通过实例评估表明该评估模型准确可靠。